Line Item SupplyIndustrial Equipment
Request a Quote

Loading dock · guide

Truck apron and door spacing: the guide

A driver backing a 53-foot trailer into a door needs more than 53 feet; the apron is where most sites run out of room, and it is the hardest thing to fix later.

Open the calculator

Why this number matters

The apron is the pavement from the dock face out to the first obstruction: a fence, a curb, a parked trailer, the building across the court. To back in square, a driver pulls past the door, cuts the tractor, and jackknifes the trailer into the position, which takes the length of the rig plus room to swing. Fifty-three feet of trailer and twenty of tractor is 73 feet standing straight; add the swing and 130 feet is the planning figure most developers use for 90-degree docks, 135 with sleeper cabs.

Door spacing changes it. At 12-foot centers the trailers at the next doors leave a 102-inch trailer about 20 inches of air each side, so the driver has to be lined up before the back end enters the gap, which takes apron. At 14-foot centers there is room to correct. Saw-tooth docks at 45 degrees cut the apron by a third at the cost of about six feet more dock face per door, and are the usual answer on a tight site.

The number to protect is the apron depth: the dock face can be extended and doors added, but the pavement between the dock and the property line is set when the building is placed.

How it is figured

  • A 90° dock needs the full tractor-trailer length plus room to swing: about 55 ft of maneuvering with 14 ft door centers, more as the centers tighten. A 53 ft trailer with a day cab therefore wants about 130 ft of apron.
  • A 45° saw-tooth dock cuts the apron to roughly 85% of the combination plus 30 ft, at the cost of about 6 ft more dock face per door.

A worked example

A 53-foot trailer with a day cab is a 73-foot rig. At 12-foot door centers the maneuvering allowance is about 65 feet, so the apron wants 138 feet from the dock face. Ten doors at 12 feet take 120 feet of dock face.

The tool's starting values, and what it returns for them:

Longest trailer53 ft
Tractor20 ft
Door center spacing12 ft
Number of doors10
Approach90°, straight back to the dock
Apron depth from the dock face138 ft
Dock face length120 ft
Tractor and trailer73 ft
Maneuvering allowance65 ft

Mistakes that catch people

  • Planning the court from the trailer length alone and finding the drivers cannot get square.
  • Parking trailers across the court from the doors with no allowance: a 53-foot trailer parked opposite needs about 185 feet of court.
  • Forgetting the drive lane for trucks passing behind the ones at the doors.

Rules of thumb

  • 130 to 135 feet for 53-foot trailers at 90 degrees; 120 for 48-foot trailers.
  • 12-foot door centers minimum, 14 is comfortable.
  • 45-degree saw-tooth: about two-thirds the apron, 1.5 times the dock face per door.

When to stop calculating and make a call

  • Double trailers, B-trains, or tankers use the dock.
  • The site slopes: a declined approach changes the dock design as well as the apron.

Questions people ask

How deep should a truck court be?
Most developers plan 130 to 135 ft from the dock face for 53-foot trailers at 90°, 120 ft for 48-foot trailers, and 185 ft or more where trailers park across the court from the doors.

Standards and sources

  • Kelley / Rite-Hite dock design guides (apron depth tables)
  • ITE, Transportation and Land Development (truck maneuvering)

This guide and the tool are planning aids. The equipment maker, the engineer of record, the accountant, or the code official confirms the final number for your building.