Loading dock · guide
Dock door size: the guide
The door has to clear the tallest trailer that comes to it with the seal that will be on it, and no more; every foot of extra door is a foot of seal the trailer never touches.
Why this number matters
A dock door's height is set by the trailer, not the building. On a 48-inch dock a 13'-6" trailer's roof is 10 feet above the floor, so a 10-foot door clears it, a 9-foot door with an 18-inch head pad seals it, and an 8-foot door is too low for a lot of the fleet. The seal decides the rest: a fixed head pad hangs below the door head and needs every trailer roof above it; a curtain header hangs 18 to 24 inches down from a taller door and meets whatever roof comes.
Width is about what passes through. An 8-foot door takes a counterbalance forklift with a pallet; 9 feet lets a driver move faster without clipping a jamb; 10 feet passes two pallets side by side or a wide load. Wider doors cost more to heat and seal, and a 10-foot-wide seal with a 10-foot door is a lot of foam at a position that sees 8'-6" trailers all day.
The common pairs are 8 by 9 with an 18-inch head pad for a dedicated van fleet, and 9 by 10 with a curtain header for a mixed fleet. Either way the opening, the seal, the bumpers, and the leveler are one decision.
How it is figured
- The trailer top sits (trailer height − dock height) above the dock floor. With a head-pad seal the pad closes the top, so the door head can be about 6 inches below the tallest trailer roof; with a curtain header it should be 6 inches above; with no seal, 12 inches above.
- Standard sectional door heights run 8, 9, 10, 11, and 12 feet; 8 feet wide fits a forklift, 9 or 10 feet for wide loads or two pallets.
A worked example
A 13'-6" trailer on a 48-inch dock puts its roof 114 inches above the floor. With a head-pad seal the door head can sit 6 inches below that, 108 inches, so a 9-foot door with an 18-inch pad does it; with a curtain header the door needs to be 120 inches, a 10-foot door.
The tool's starting values, and what it returns for them:
| Dock height | 48 in |
| Tallest trailer served | 13' 6" |
| Seal at the door | Dock seal with head pad |
| Equipment through the door | Counterbalance forklift, 8' wide is enough |
| Door to order | 8' wide x 9' high |
| Trailer top above the dock floor | 114 in |
| Height needed | 108 in |
| Standard height | 108 in |
Mistakes that catch people
- Specifying 10 by 10 everywhere and then paying for seals that never compress.
- An 8-foot door with a head pad on a dock that sees 13'-6" trailers: the pad is crushed daily.
- Forgetting the dock height: the same trailer needs a foot more door on a 36-inch dock.
Rules of thumb
- Trailer roof above the floor = trailer height − dock height.
- Head pad: door head 6 inches below the lowest roof you serve. Curtain: door head 6 inches above the tallest.
- 8 feet wide for forklifts, 9 for speed, 10 for double pallets.
When to stop calculating and make a call
- The dock also serves straight trucks and vans with roofs well below the trailers; the seal choice gets specific.
- Cold storage: door height, seal, and vestibule are a package.
Questions people ask
- Why are most dock doors 8 by 9 or 9 by 10?
- On a 48-inch dock a 13'-6" trailer tops out 10 feet above the floor. An 8 by 9 door with an 18-inch head pad seals it; a 9 by 10 door with a curtain header seals the whole range of trailers and lets wider loads through.
Standards and sources
- Loading Dock Supply, dock seal FAQ (head pad and curtain header selection by door height)
- DASMA and door manufacturer standard sizes
This guide and the tool are planning aids. The equipment maker, the engineer of record, the accountant, or the code official confirms the final number for your building.