Line Item SupplyIndustrial Equipment
Request a Quote

Loading dock · guide

Dock bumper projection: the guide

On a declined approach the trailer leans into the building. The bumpers, not the wall, have to be what it leans on, and the amount is simple geometry.

Open the calculator

Why this number matters

A trailer on level ground sits square; its back is vertical and the bumpers meet it at one height. Back the same trailer down a drive that slopes toward the building and the whole trailer tilts nose-up: the back face now leans toward the wall, and the top of the trailer, nine feet above the bumper line, is closer to the building than the bumper face by the grade times that height. On a four percent decline that is more than four inches. If the bumpers project four inches, the top of a 13'-6" trailer touches the wall above the door before the bumpers touch anything.

The fix is bumper projection: enough that the trailer top still clears the wall by a few inches when the bumpers are compressed. Laminated bumpers come in 4, 4.5, 6, 8, 10, and 12 inches and deeper; above about ten inches the leveler lip has to reach further too, and the usual answer becomes a projected dock, where the leveler pit cantilevers out from the wall and the whole problem moves outboard.

The same lean is why dock seals on a decline are tapered and why the top of the door frame on a declined dock has the scars. The three fixes, deeper bumpers, tapered seals, and a projected pit, are the same calculation seen from three sides.

How it is figured

  • On a decline the trailer sits nose-high and its back leans toward the wall by the grade times the height above the bumper line: (trailer height − dock height) × grade.
  • Bumper projection = the clearance you want at the trailer top plus that lean; standard laminated bumpers come in 4, 4.5, 6, 8, 10, 12 inches and deeper.

A worked example

A 13'-6" trailer on a 48-inch dock has 114 inches of back face above the bumper line. On a 3% decline that leans 3.4 inches toward the wall; with 4-inch clearance wanted, the bumpers need 7.4 inches and the standard order is 8-inch.

The tool's starting values, and what it returns for them:

Dock height48 in
Tallest trailer served13' 6"
Decline of the approach3 %
Clearance to keep4 in
Bumper projection needed7.4 in
Standard bumper to order8 in
Trailer top leans toward the wall3.4 in
Clearance with 4-inch bumpers0.6 in
with 6-inch bumpers2.6 in
with 10-inch bumpers6.6 in

Mistakes that catch people

  • Measuring the grade near the building only: the trailer's angle is set over its whole length, so measure over 50 feet.
  • Ordering 6-inch bumpers for a 6% decline because the number sounded right: at 6% the lean alone is nearly seven inches.
  • Forgetting the leveler: deeper bumpers move the trailer bed out, and a short leveler lip loses its purchase.

Rules of thumb

  • Lean in inches is about one inch per percent of grade for a standard trailer on a standard dock.
  • Keep four inches between the trailer top and the wall at full bumper compression.
  • Past 10% decline, project the dock.

When to stop calculating and make a call

  • Trailers taller than 13'-6" or double-stacked step vans come to the door.
  • The leveler is already short on lip; bumper depth and leveler length are chosen together.

Questions people ask

What happens if the bumpers are too short?
The top of the trailer hits the wall above the door, which cracks block, bends the door frame, and crushes the dock seal's head pad. On a 4% decline a 13'-6" trailer on a 48" dock leans about 4.5 inches, so standard 4-inch bumpers leave nothing.

Standards and sources

  • Pentalift, declining approach and dock bumper projection guidance
  • Loading Dock Supply, dock seal and bumper FAQ (keep the trailer 4 inches off the wall)

This guide and the tool are planning aids. The equipment maker, the engineer of record, the accountant, or the code official confirms the final number for your building.