Line Item SupplyIndustrial Equipment
Request a Quote

Loading dock · guide

Dock leveler length and working range: the guide

A leveler is a ramp between the dock floor and a trailer bed that is almost never at the same height. Its length sets the slope of that ramp, and the slope decides whether a pallet jack can climb it.

Open the calculator

Why this number matters

Trailer beds are not 48 inches. A 53-foot dry van sits at 48 to 54 inches depending on its load and its suspension; a reefer runs a couple of inches higher; flatbeds and containers on chassis sit near 56 to 62; a straight truck or a cube van can be down at 36 to 44. A dock built at 48 inches meets all of them with a leveler that lifts above the dock for the high beds and drops below it for the low ones. The working range on the order has to cover the worst case in each direction, with a few inches of margin for the trailer settling as it is loaded.

The length then sets the grade. Eight inches of difference over a 6-foot leveler is an 11% ramp; over 8 feet it is 8%; over 10 feet it is under 7%. A sit-down counterbalance forklift climbs 10% without complaint. An electric pallet jack with a 6-inch load clearance bottoms out, spins its drive wheel, or stalls somewhere around 7%, and a load on a tall mast tips a little further at every percent. The longer the leveler, the gentler the grade, the slower the wear on the lip hinge, and the fewer the dropped loads.

Longer costs more in the pit and the unit, and 10- and 12-foot levelers take up floor behind the door. That is why most mixed docks land at 8 feet, and why docks that serve flatbeds and containers from a 48-inch floor, or run electric pallet jacks, go to 10 or 12.

How it is figured

  • Above-dock range = highest trailer bed − dock height; below-dock range = dock height − lowest trailer bed, each at least 0.
  • Worst case = the larger of the two. Grade at each length = worst case ÷ leveler length, as a percent, for 6, 8, 10, and 12 feet.
  • The pick is the shortest standard length whose grade is at or under the limit you set: 10% for counterbalance forklifts, 7% for electric pallet jacks and low-clearance loads.
  • Order the working range with a few inches of margin each way; air-ride trailers settle as they load.

A worked example

A 48-inch dock serves everything from cube trucks at 40 inches to loaded vans at 56. That is 8 inches above and 8 inches below the dock. A 6-foot leveler would put an 11% grade on the worst case; 8 feet brings it to 8.3%, under the 10% limit for counterbalance trucks, so 8 feet is the shortest length that works.

The tool's starting values, and what it returns for them:

Dock height48"
Lowest trailer bed40"
Highest trailer bed56"
Grade limit10%
Shortest length under the limit8 ft
Working range above the dock8"
Working range below the dock8"
Grade at 6'11.1%, over the limit
Grade at 8'8.3%
Grade at 10'6.7%
Grade at 12'5.6%

How to get the bed heights

  1. List the trailer and truck types that come to the door over a month: dry vans, reefers, flatbeds, containers, straight trucks, cube vans.
  2. For each, take the bed height from the table in the calculator or measure a few at the door with a tape from the drive to the bed, empty and loaded.
  3. Measure the dock height from the drive at the door to the dock floor. On a sloped approach measure where the rear axles sit, not at the wall.
  4. Enter the dock height and the lowest and highest beds you found.

Tools: a tape, the carrier list, a few minutes at the door on a busy day

Mistakes that catch people

  • Assuming every trailer is 48 inches. The straight truck that comes twice a week is what the below-dock range is for.
  • Sizing the grade for the forklift when the night shift unloads with electric pallet jacks.
  • Ordering a leveler with no below-dock range and discovering that the bumpers and the restraint do not allow it either.
  • Forgetting that the approach slope and air-ride settling change the bed height at the door by several inches.
  • Choosing 6 feet to save on the pit and paying for it in lip hinges and spilled loads.

Rules of thumb

  • 8 feet for a mixed dock; 10 or 12 for flatbeds, containers, or pallet jacks.
  • 10% is the ceiling for sit-down forklifts; 7% for walkies and low-clearance loads.
  • Working range: 12 inches above and 12 below the dock covers most mixed fleets.

When to stop calculating and make a call

  • The dock is not 48 inches, or trailers with beds more than a foot off the dock height are regular: the maker sizes the leveler and the pit together.
  • The approach is declined: the bumpers, the seal taper, and the leveler lip are one decision.
  • A vehicle restraint is going in: its reach has to match the leveler's below-dock travel.

Questions people ask

What grade is too steep?
Counterbalance forklifts handle about 10%. Electric pallet jacks, walkies, and low-clearance loads want 7% or less, and a long leveler is cheaper than a damaged load or a stuck jack.
Why would a 48-inch dock need range below the dock?
Loaded straight trucks, cube vans, and some drop-deck trailers sit below 48 inches, and a loaded van on air suspension settles several inches during unloading.
How long should the leveler be?
The length that keeps the worst-case grade under the limit. Most mixed docks land at 8 feet; docks serving flatbeds or containers from a 48-inch floor, or with electric pallet jacks, go to 10 or 12 feet.
Does the approach slope matter?
Yes. An apron that slopes toward the building tilts the trailer so the rear sits higher than its level bed height. Add the effect of the slope to the bed heights you enter and check the door head height.

Standards and sources

  • Dock leveler makers' sizing guides: working range and grade by leveler length and trailer bed height
  • Lift truck makers' operating guidance on ramp grades for counterbalance trucks and pallet jacks

This guide and the tool are planning aids. The equipment maker, the engineer of record, the accountant, or the code official confirms the final number for your building.