Line Item SupplyIndustrial Equipment
Request a Quote

Material handling and racking · guide

Forklift ramp grade: the guide

Grade is rise over run, and the limit depends on who climbs it: a loaded forklift about 10%, an electric pallet jack 7, a hand jack 5, a person in a wheelchair 8.33.

Open the calculator

Why this number matters

A ramp's grade is its rise divided by its run, as a percent; the angle is the arctangent. A loaded counterbalance truck is rated for 10 to 15% on dry concrete, and most fleets set the limit at 10 because tires slip on a wet or dusty ramp and the load must be carried uphill forward and downhill in reverse. Electric pallet jacks lose traction and brake authority above about 7%, a manual jack is a struggle past 5 because the operator pulls the load, and an accessible route is 1 in 12 by law with landings every 30 inches of rise.

Yard ramps are where the question comes up most. A 48-inch dock over a 36-foot ramp is 11%, the common standard length; 30 feet is 13% and is for light loads. The calculator gives the run that hits each limit so the ramp can be specified rather than argued about.

The surface length is longer than the run by the hypotenuse, which matters for grating and for the forklift's underside clearance at the top and bottom breaks.

How it is figured

  • Grade = rise ÷ run × 100; angle = arctan(rise ÷ run). Run for a limit = rise ÷ limit.
  • Limits: forklift makers rate loaded travel at 10 to 15% on dry surfaces and many fleets set 10%; electric pallet jacks about 7%; manual pallet jacks 5% because the operator pulls the load; ADA accessible routes 1:12 (8.33%) with landings every 30 inches of rise.

A worked example

A 48-inch rise over a 420-inch run is 11.4%, 6.5 degrees, 1:8.75; a loaded forklift wants 480 inches of run for 10%, a 40-foot ramp.

The tool's starting values, and what it returns for them:

Rise48 in
Run420 in
What uses itSit-down forklift, loaded (limit about 10%)
Grade11.4 %
Angle6.5 °
Run for 10%480 in
Ratio1:8.8
Ramp surface length423 in
  • 11.4% is over the 10% that a loaded forklift should climb; lengthen the run to 40'-0" or lower the rise.

Mistakes that catch people

  • Confusing degrees and percent: 10% is 5.7 degrees, 10 degrees is 17.6%.
  • Measuring the run along the slope instead of horizontally.
  • Carrying the load downhill forward: OSHA says forks downgrade with a load.

Rules of thumb

  • Forklift 10%, electric pallet jack 7%, manual jack 5%, ADA 8.33%.
  • Percent = rise ÷ run × 100; degrees ≈ percent × 0.57 for small grades.
  • 36-foot yard ramp on a 48-inch dock: 11%.

When to stop calculating and make a call

  • Ramps on public ways or accessible routes: the building code and the ADA Standards.
  • Grades near the forklift's limit with loads near its capacity: the truck maker's gradeability chart.

Questions people ask

Why do yard ramps run 30 to 36 feet?
A 48 in. dock over a 36 ft ramp is 11%, the most a loaded forklift should take; a 30 ft ramp is 13% and is for lighter loads or empty travel. Longer is safer and costs more steel.

Standards and sources

  • OSHA 1910.178(n) (grades, forks downgrade with a load)
  • ADA Standards 405 (ramp slope 1:12)
  • Forklift and yard ramp manufacturer gradeability ratings

This guide and the tool are planning aids. The equipment maker, the engineer of record, the accountant, or the code official confirms the final number for your building.