Line Item SupplyIndustrial Equipment
Request a Quote

Air, heating, and ventilation · guide

Air changes and exhaust CFM: the guide

Ventilation is sized in air changes an hour, and the right number depends on what the room does; the cfm, the fans, and the intake they need all fall out of it.

Open the calculator

Why this number matters

An air change is one room volume of outside air an hour. General storage runs on two to four; a warehouse with forklifts and docks four; a battery charging room six, set by the hydrogen the chargers make; machine shops and welding higher still; paint areas thirty and up, by the fire code and the finish. Volume times the rate over sixty is the cfm, and dividing by a fan's rating is the fan count, which for a warehouse is usually a few 36- or 48-inch wall fans.

The forgotten half is the intake. Exhaust fans only move the air that can get in, and a tight building starves them; the air then comes through the dock seals, the door gaps, and the flue of the water heater. Louvers or open doors with about 500 feet per minute across their free area let the fans do their work. In winter the make-up air is heated air, which is why ventilation is sized to what the room needs and not more.

Specific hazards have their own rules that override the general rates: propane forklifts by the truck count, hydrogen from charging by the charger current, solvent storage and spray finishing by the fire code; the related calculators cover the first.

How it is figured

  • cfm = room volume × air changes per hour ÷ 60. Air change rates are the common industrial design figures; codes and insurers set higher rates for specific hazards.
  • Exhaust needs make-up air: the intake free area at about 500 feet per minute face velocity.

A worked example

A 200 by 100 by 24 foot room is 480,000 cubic feet; at four changes an hour that is 32,000 cfm, four 10,000-cfm wall fans, and 64 square feet of intake louver.

The tool's starting values, and what it returns for them:

Room length200 ft
Room width100 ft
Ceiling height24 ft
Air changes per hour4, warehouse with forklifts, docks
Exhaust fan rating10,000 cfm
Exhaust airflow32,000 cfm
Fans4
Room volume480,000 cu ft
Make-up air opening at 500 fpm64 sq ft free area

Mistakes that catch people

  • Exhaust without intake, then wondering why the doors are hard to open and the fans are loud.
  • Ventilating a warehouse at ten changes an hour all winter and heating the outdoors.
  • Using general rates where a code sets a specific one (paint, battery rooms, flammable storage).

Rules of thumb

  • Storage 2 to 4 ACH, active warehouse 4, charging rooms 6, welding 10, paint 30.
  • cfm = volume × ACH ÷ 60.
  • Intake free area at about 500 fpm: cfm ÷ 500 square feet.

When to stop calculating and make a call

  • Any room with a code-driven rate (battery charging, spray finishing, hazardous storage): the mechanical engineer and the code official.
  • Heat recovery on large make-up air volumes.

Questions people ask

How many air changes does a warehouse need?
Two to four per hour is the usual planning figure for general storage and dock areas; propane forklifts are better handled by the per-truck rule (see the forklift exhaust calculator). Battery charging rooms, paint, and welding are set by the specific codes and are much higher.
Will the exhaust fans work without intake?
No. A tight building starves the fans and pulls air through the dock seals and doors instead; size the louvers to the cfm.

Standards and sources

  • ASHRAE Standard 62.1 and HVAC Applications (industrial ventilation)
  • ACGIH, Industrial Ventilation: A Manual of Recommended Practice

This guide and the tool are planning aids. The equipment maker, the engineer of record, the accountant, or the code official confirms the final number for your building.