Cleanrooms and dry rooms · guide
Dry room dew point converter: the guide
Dry rooms are specified in dew point because humidity meters cannot read the moisture they hold; the converter puts the dew point in the units the dehumidifier and the process engineer use.
Why this number matters
At the dew points lithium battery work needs, −40°C and below, the air holds less than a tenth of a gram of water per kilogram, which is half a percent relative humidity at room temperature. A humidity sensor reads zero; a chilled-mirror or capacitive dew point sensor reads it directly, and the dew point does not change when the room temperature does, which is why the spec is written that way.
The other units still come up. Grains per pound is what North American dehumidifier capacity is quoted in, grams per kilogram is the metric equivalent, and parts per million by volume is how the gas analyzers and the process chemists talk. Below freezing the conversion runs over ice, not water, and the two curves differ enough to matter at −40.
The converter is the bridge between the spec, the sensor, and the equipment data sheet, and it answers the question that comes up in every dry room meeting: what does −40 actually mean in the units on this quote.
How it is figured
- Vapor pressure at the dew point from the Magnus formula, over water above 0°C and over ice below (coefficients 22.46 and 272.62); humidity ratio = 622 × pw ÷ (101.325 − pw) in g/kg at sea level; grains = g/kg × 7; ppmv = pw ÷ atmospheric pressure; RH = pw ÷ the saturation pressure at room temperature.
A worked example
A −40°C dew point is −40°F, 0.079 grams per kilogram, 0.55 grains per pound, 128 parts per million of water vapor, and 0.49% relative humidity in a 22°C room.
The tool's starting values, and what it returns for them:
| Dew point | -40 °C |
| Dew point entered in | °C |
| Room temperature | 22 °C |
| Humidity ratio | 0.079 g/kg |
| Grains per lb of dry air | 0.55 |
| Water vapor | 127 ppmv |
| Relative humidity at 22°C | 0.49 % |
| Dew point | -40 °F |
| Dew point | -40 °C |
Mistakes that catch people
- Converting a sub-freezing dew point with the over-water formula; the humidity ratio comes out about 10% high at −40.
- Reading a −40°C spec as −40°F and thinking the two differ; they are the one temperature where they do not.
- Setting a humidity alarm in percent RH in a dry room; the sensor cannot resolve it.
Rules of thumb
- −40°C dew point ≈ 0.08 g/kg ≈ 0.5% RH at room temperature.
- −60°C ≈ 0.007 g/kg, ten times drier again.
- Each 10°C of dew point is roughly a factor of 2.5 in moisture.
When to stop calculating and make a call
- Choosing the sensor: dew point transmitters drift and need calibration schedules the maker sets.
- The process spec is in ppm and the room spec in dew point: agree the conversion basis with the process engineer.
Questions people ask
- Why is a dry room specified by dew point and not humidity?
- At −40°C dew point the air holds 0.08 g of water per kg, which is 0.5% relative humidity at 22°C; humidity meters cannot read that, dew point sensors can, and the number does not change with the room temperature. Lithium electrolytes and lithium metal react with that little water, which is why cell plants hold −40 and some processes −60.
Standards and sources
- ASHRAE Handbook, Fundamentals, Psychrometrics (Hyland-Wexler basis; Magnus fit used here)
This guide and the tool are planning aids. The equipment maker, the engineer of record, the accountant, or the code official confirms the final number for your building.