Energy and payback · guide
Compressed air leak cost: the guide
Compressed air is the most expensive utility in the plant, and a plant without a leak program loses a quarter of it through holes you can hear from the aisle.
Why this number matters
A compressor turns about eight units of electricity into one unit of useful air, so every cubic foot that escapes through a cracked hose or an open coupler costs eight times what the same flow would cost as electricity. The Department of Energy's leak table gives the flow for a hole at 100 psig: 6.5 cfm through a sixteenth-inch hole, 26 through an eighth, 104 through a quarter, and the compressor power to make it is the cfm times the unit's specific power, about 18 kW per 100 cfm for a lubricated screw.
A dozen eighth-inch leaks is 300 cfm, which is a 60-horsepower compressor running for nothing, around $25,000 a year at 6,000 hours. Surveys in plants without a program find 20 to 30% of the output leaking; a program with an ultrasonic detector, tags, and a monthly walk gets it under 10%.
Pressure is the other lever: every 2 psi above what the farthest tool needs costs about 1% in power and makes every leak leak more. The compressor sizing calculator takes the leak allowance as an input for that reason.
How it is figured
- Leak flow from the orifice table in the U.S. DOE / Compressed Air Challenge fact sheet: at 100 psig a 1/16 in. hole passes about 6.5 cfm, 1/8 in. 26, 1/4 in. 104, 3/8 in. 234; scaled by absolute pressure for other line pressures.
- Compressor power = cfm × specific power (kW per 100 cfm); energy = kW × hours; cost at the rate.
A worked example
An eighth-inch leak at 100 psig passes 26 cfm, takes 4.7 kW of compressor to feed, and over 6,000 hours at 12 cents costs $3,370 a year; ten of them are $33,700, a figure that pays for a leak survey in the first week.
The tool's starting values, and what it returns for them:
| Leak size | 1/8 in. (a cracked hose) |
| Line pressure | 100 psig |
| Leaks like this in the plant | 10 |
| Compressor hours per year | 6,000 h |
| Electricity rate | 0.12 $/kWh |
| Compressor specific power | 18 kW per 100 cfm |
| Cost per leak per year | 3,370 $ |
| Cost of 10 leaks per year | 33,696 $ |
| Air lost per leak | 26 cfm |
| Compressor power per leak | 4.68 kW |
| kWh per leak per year | 28,080 |
- 260 cfm of leaks is a compressor's worth; a leak survey with an ultrasonic detector pays back in weeks.
How to find the leaks
- Walk the plant during a quiet shift with an ultrasonic leak detector, or soapy water on fittings; tag each leak with its size and location.
- Read the line pressure at the header gauge.
- Compressor hours from its hour meter or the control panel; the specific power from its data sheet (or 18 kW per 100 cfm for a rotary screw).
Tools: ultrasonic leak detector (rent one), tags, the compressor's hour meter
Mistakes that catch people
- Fixing leaks once and not walking again; new ones open every month.
- Hunting leaks during a loud shift; the detector works best on a quiet one.
- Running the header at 110 psi because one tool was starved; fix the piping to that tool instead.
Rules of thumb
- At 100 psig: 1/16 inch 6.5 cfm, 1/8 inch 26, 1/4 inch 104.
- About 18 to 22 kW per 100 cfm for a lubricated screw at 100 psig.
- Every 2 psi of header pressure is about 1% of power.
When to stop calculating and make a call
- A full audit with data logging: compressed air specialists do a week of logging for a few thousand dollars and usually find more than leaks.
- Controls on multiple compressors: sequencing is a systems question.
Questions people ask
- How much of a plant's air is leaks?
- DOE surveys put it at 20 to 30% of compressor output in plants without a leak program, and under 10% with one. A dozen 1/8 in. leaks at 100 psig cost about as much as running a 25 hp compressor for nothing.
Standards and sources
- U.S. DOE, Compressed Air Tip Sheet 3: Minimize Compressed Air Leaks (leak flow table)
- Compressed Air Challenge, Best Practices for Compressed Air Systems
This guide and the tool are planning aids. The equipment maker, the engineer of record, the accountant, or the code official confirms the final number for your building.