Loading dock calculator
Dock seal thickness and taper for a sloped approach
Give it the door size, the dock height, the bumpers, and how much the drive drops or rises over 50 feet. It draws the trailer leaning at that grade and returns the side pad projection at the bottom and the top, the taper, the head pad or curtain, the overall unit size, and the bumper projection that keeps the top of the trailer off the wall.
- Declined or inclined approach, any grade.
- Compression held between 4" and 6" top to bottom.
- One line to hand the seal maker, ready to copy.
Need the seal quoted?
Send the door count and these numbers and the quotation comes back with the seals, bumpers, and installation as line items.
Dock equipmentDock seal size and taper for the approach
How to measure the slope
Three steps, one helper, a ball of string, a line level, and a tape. Type the two readings above and the calculator does the rest.
- 1. Tie off at floor level. Hook the string to the dock floor edge at the door, or hold a tape at the dock height on the wall.
- 2. Pull it out level. Walk straight out along the trailer path about 50 feet (one trailer length). Hang a line level on the string, or shoot the line with a laser level, and hold the far end so the bubble is centered.
- 3. Measure down. At the far end, measure from the string straight down to the ground. Less than the dock height means the drive declines toward the building; more means it rises.
Grade = the difference between the two readings divided by the distance out, both in inches: 12" over 600" is 2%. A rotary laser at dock floor height and a grade rod at 50 feet give the same two numbers faster.
What the trailer does at that grade
Approach grade
2% declined
The trailer leans 2" toward the wall over the pad height.
Side pads
10" → 8"
bottom to top, 2" taper, thicker at the bottom; 12" wide x 8'-0" tall
Head
18" head pad
fixed foam head pad; unit 9'-6" x 9'-6" overall, 7'-6" inside
- With 4" bumpers the top of a 13'-6" trailer comes within 1 3/4" of the wall. Use 7" bumpers or a projected dock to keep 4".
- Straight pads would compress 8" at the top, over the 6" limit; order the taper.
- Compression at the bumper line
- 6" (4" to 6" allowed)
- Compression at the top with straight pads
- 8"; with the taper, 6" top to bottom
- Top of the highest trailer to the wall
- 1 3/4" with 4" bumpers; 7" bumpers keep 4"
- Door head
- 12'-0" above ground; Every trailer roof clears the door head by at least 6", so a fixed 18" head pad seals the top; it reaches 13'-6".
What to tell the seal maker
8'-0" x 8'-0" door, 48" dock, 4" bumpers, 2% declined approach; foam dock seal: side pads 12" wide x 8'-0", tapered 10" at the bottom to 8" at the top; 18" fixed head pad; 7'-6" inside, 9'-6" x 9'-6" overall; trailers 12'-6" to 13'-6".
Measure the grade with a string held level at the dock floor and run out 50 feet; the drop to the ground divided by 600 inches is the grade. Taper = grade x pad height, which is the maker's rule of about 1" per 1% on a standard pad. Compression is held to 4" minimum and 6" maximum; the top of the trailer is kept at least 4" off the wall. The seal maker confirms the model, foam density, and mounting on the order.
Read the guide: what the number means and how to use it
Questions dock managers ask
- Why does a sloped approach change the dock seal?
- On a declined approach the drive slopes down toward the building, so the trailer sits nose-high and its back leans toward the wall. The top of the trailer is closer to the building than the bumper line by the grade times the height above the bumpers: on a 4% decline the top of an 8-foot pad is about 4 inches closer. A straight seal is over-compressed at the top and the trailer can hit the wall above the door. Tapered side pads, thicker at the bottom than the top by that amount, keep the compression even. On an incline the trailer leans away and the pads taper the other way, thicker at the top.
- How do I measure the grade?
- Hold a string level at the dock floor and run it 50 feet straight out along the trailer path. Measure from the string down to the ground at the far end. That drop divided by 600 inches is the grade: a 12-inch drop is 2%, an 18-inch drop is 3%. Most makers want declines held under 10%.
- How much projection should the side pads have?
- About 5 inches more than the bumper projection on a level dock, so a 4-inch bumper takes a 10-inch pad and a 14-inch bumper takes a 20-inch pad. The pads should compress at least 4 inches so a trailer parked slightly off still seals, and no more than 6 inches or 45% of the projection so the foam and the wall are not overloaded. On a decline, project the bumpers first so the top of the trailer stays at least 4 inches off the wall, then size the pads from the new bumper face.
- Head pad or curtain header?
- A fixed foam head pad seals the top when every trailer's roof is above the door head, which is the case for 8-foot doors on a 48-inch dock with 12-foot-6 to 13-foot-6 trailers. When the door is 9 feet or taller the lowest trailers sit below the door head, so a drop curtain header, 18 to 24 inches, hangs down to meet the roof; an adjustable header suits a wide mix of trailers.
- Does this replace the seal maker's survey?
- No. It gives you the size, the taper, and the numbers to check a quotation against. The maker confirms the model, the foam density, the pleats, and the mounting from the door survey, and projections over 20 inches usually point to a dock shelter instead.
More calculators: dock leveler capacity, leveler length and working range, gable endwall panels.