Line Item SupplyIndustrial Equipment
Request a Quote

Material handling and racking · guide

Mezzanine floor and column loads: the guide

A mezzanine is specified by its live load in pounds per square foot, and the column loads that follow are what the slab and the engineer have to carry.

Open the calculator

Why this number matters

The building code sets the minimum live loads by use: 50 psf for an office, 125 for light storage, 250 for heavy storage; the deck and the steel add about 15 psf of dead load. Most storage mezzanines are quoted at 125 psf, which covers shelving, pick modules, and carts, and 250 where pallets will be staged on the deck. Each interior column carries its tributary area, the column spacing each way, times the total load, and delivers it to the slab through a base plate.

The slab is the usual surprise. A 20 by 15 foot column grid at 125 psf puts 42,000 pounds on an interior column, 290 psi on a 12-inch base plate, more than a 6-inch slab on grade is normally good for; the mezzanine maker's engineer either enlarges the plates, tightens the grid, or calls for footings under the columns. Knowing the number before the quote avoids the change order.

Stairs, guardrail, gates, and the egress path are part of the same design, and the occupant load on the deck decides whether one stair is enough.

How it is figured

  • Live load from the use (IBC Table 1607.1: offices 50 psf, light storage 125, heavy storage 250) plus about 15 psf dead load for the deck and framing.
  • An interior column carries its tributary area (column spacing each way) times the total load; base plate pressure is that over the plate area. Edge and corner columns carry half and a quarter.

A worked example

A 40 by 30 foot mezzanine at 125 psf with 15 psf dead load carries 168,000 pounds; on a 20 by 15 foot grid an interior column takes 42,000 pounds, which on a 12 by 12 inch base plate is 292 psi, a number that sends the engineer to the slab drawings.

The tool's starting values, and what it returns for them:

Mezzanine length40 ft
Mezzanine width30 ft
UseLight storage, shelving and pick modules (125 psf)
Column spacing along the length20 ft
Column spacing across the width15 ft
Column base plate12 x 12 in.
Design live load125 psf
Load on an interior column42,000 lb
Pressure under the base plate292 psi
Total design load168,000 lb
Columns9
Area1,200 sq ft
  • 292 psi under the base plates is more than a 6 in. slab on grade usually takes without footings; the mezzanine maker's engineer will call for a slab check or pads.

Mistakes that catch people

  • Quoting an office mezzanine at 50 psf and then using it for storage.
  • Assuming the slab takes whatever the columns deliver.
  • Forgetting the second stair: over 49 occupants or a long travel distance needs two exits.

Rules of thumb

  • Office 50 psf, light storage 125, heavy storage 250; add 15 dead.
  • Column load = tributary area × total load; base plate psi = load ÷ plate area.
  • Over about 150 psi on a 6-inch slab, expect footings or bigger plates.

When to stop calculating and make a call

  • Every mezzanine: the maker's stamped engineering and a building permit are required almost everywhere.
  • Equipment on the deck (racks, conveyors, machines): their point loads go to the engineer.

Questions people ask

What live load should I specify?
125 psf covers most storage and pick modules and is the common quote basis; offices need 50 but are usually built at 125 anyway so the space can change use; pallets staged on the deck need 250 and heavier framing.

Standards and sources

  • IBC Table 1607.1, minimum uniformly distributed live loads
  • Mezzanine manufacturer design practice (Cogan, Wildeck, Steele Solutions)

This guide and the tool are planning aids. The equipment maker, the engineer of record, the accountant, or the code official confirms the final number for your building.