Plant floor problems · Dock Equipment
Dock seal vs dock shelter: which one for your doors
Reviewed October 16, 2026. Official sources are linked where they exist.
Short answer
A compression dock seal is a set of foam pads the trailer backs into, compressing them 4 to 6 inches to form a gasket around the rear of the trailer. It gives the tightest seal and suits doors up to about 9 feet wide by 10 feet high with a consistent trailer size. A dock shelter is a frame projecting roughly 24 inches from the wall with head and side curtains that wipe along the trailer, so it handles larger doors, from 10 by 10 up to 12 by 12 and beyond, and a mixed fleet of trailer heights and widths, at the cost of a slightly looser seal. Inflatable designs fill the gap after the trailer docks and serve mixed fleets where the wall cannot take compression force. Air moves through an open dock opening at roughly 3 feet per second, which is the loss both products exist to stop. Send the door size, the wall-to-bumper projection and your trailer mix and the quotation names the right one with freight to your dock included.
How each one seals the opening
A compression seal is two vertical foam pads and a head pad, each wrapped in a wear fabric, mounted to the wall around the door. The trailer backs in and presses the pads 4 to 6 inches until the rear of the trailer sits against the bumpers, so the seal is a gasket formed by compression against the trailer's rear face. The pads cover part of the door opening while compressed, which is why the design works best on smaller doors and why oversized loads can rub the pads on the way out.
A shelter is a three-sided frame, rigid or flexible, projecting from the wall and carrying a head curtain and two side curtains. The trailer backs through the frame and the curtains wipe along the trailer's top and sides, leaving the full door opening clear. Because the curtains flex rather than compress, a shelter tolerates a wide spread of trailer heights and widths, but the contact is a wiper rather than a gasket, so the seal is looser than foam.
Inflatable seals and shelters add air bags or an inflatable head curtain that fill around the trailer after it is parked. They conform to whatever shows up and put little force on the wall, which matters on tilt-up or metal-skinned buildings that should not carry compression loads.
| Compression foam seal | Doors up to about 9 ft wide by 10 ft high; consistent trailer size; tightest seal; cold storage and conditioned space |
|---|---|
| Rigid-frame shelter | Doors 10 by 10 up to 12 by 12 and larger; mixed fleet; full clear opening; projection about 24 in |
| Flexible-frame shelter | Same as rigid, but the frame yields when a trailer backs in off-center; busier docks and tight approaches |
| Inflatable seal or shelter | Mixed fleet where the wall cannot take compression force; conforms after docking |
| Typical dock door opening | 8 by 8 to 10 by 10 ft; size the door to the largest trailer body, not larger |
Trailer mix decides it more than door size does
A seal is built for a trailer rear face that lands in roughly the same place every time. Dry vans of one height with roll-up or swing doors are the easy case. Mix in refrigerated trailers with thicker walls, step-decks, straight trucks and the occasional container chassis, and the pad that gaskets one trailer misses the next by a foot. Manufacturers quote a seal's coverage range in a limited band of trailer heights; outside it the gasket opens at the top or the pad takes a beating at the corners.
A shelter does not care as much. The head curtain drops to meet a short trailer and lifts for a tall one; the side curtains wipe a 96 inch or a 102 inch body alike. If your receiving dock sees whatever the carrier sends, the shelter is the default, and an inflatable head curtain closes the gap a plain curtain leaves over a low trailer.
Swing-out trailer doors leave a gap at the hinges that neither product closes by itself. Shelters with hooks or pockets that hold the swung doors against the trailer body, and side pads shaped for the hinge gap on seals, are options worth asking for if most of your trailers have swing doors.
Projection, wall force and wear
Measure a seal from the wall mounting surface to the face of the dock bumper, then add 4 to 6 inches of compression. A seal specified too deep gets crushed flat and wears out; too shallow and it never gaskets. Shelters are built in standard projections, commonly 18 to 36 inches, with about 24 inches the usual figure, and the frame carries the curtains past the bumper face so the trailer is inside the frame when it stops.
A compression seal pushes on the building every time a trailer docks. Masonry and poured concrete shrug it off. Insulated metal panel, tilt-up at a panel joint and light-gauge framing may not, and that is where inflatable designs or a shelter earn their place. Declined approaches, where the trailer sits nose-down and rises as it backs in, drive the trailer up into the head pad and shorten its life; wear pleats on the side pads and a replaceable head pad are the answer, and a shelter is often the better pick on a steep decline.
Wear is a maintenance line, not a mystery. The pad or curtain faces the trailer and gets replaced on a schedule. Buy the one whose wearing parts are sold separately and bolt on without a crew.
- Seal projection: wall to bumper face plus 4 to 6 inches
- Shelter projection: 18 to 36 inches, about 24 inches typical
- Check the wall before specifying a compression seal on metal panel or tilt-up
- Declined approach: expect head pad wear, consider a shelter
- Ask for replaceable wear faces and pads
Energy: what the opening costs when it is open
DASMA's technical data sheet on high speed doors puts air movement through an open door opening at approximately 3 feet per second. A trailer at an unsealed door leaves a ring of open area around its body for as long as it sits there, which on a busy receiving dock is most of the shift. Its dock door sheet says the plain thing: when the door is raised, shelters and seals reduce the loss of conditioned air and keep rain and snow off the platform.
Manufacturer and dealer publications claim dollar savings per dock position per year and paybacks measured in months. Treat those as the vendor's modeling, not a study. The honest version is that a tight seal matters most where the temperature difference is largest: cold storage, conditioned production, and any dock in a heating climate. Two gaps survive a good seal or shelter: the hinge gap on swing doors and the gap under the leveler, which has its own seal product.
How we quote it
Send the door width and height, the wall-to-bumper-face dimension and bumper thickness, the dock height, the approach grade, the wall construction, and the trailer mix: lowest and highest bed heights, body widths, and whether the doors swing or roll up. A photo of the door from outside with a trailer parked, or the architectural drawings for a new dock, covers most of it.
The quotation names the seal or shelter, the projection, the wear options and any under-leveler seal, with freight to your dock included. Seals and shelters go on the same quotation as the leveler, restraint and bumpers when you are doing the whole door, so the projections and the restraint position are checked together. The dock builder on this site asks the same questions if you want to work through them first.
Questions buyers ask
- Can I put a dock seal on a 10 by 10 door?
- You can, but the compressed pads intrude into the opening and the seal's trailer height range narrows as the door grows. Manufacturers' guidance puts seals at doors up to about 9 feet wide by 10 feet high and shelters above that. On a 10 by 10 with a consistent fleet, ask for both options priced.
- Which is cheaper, a seal or a shelter?
- A compression seal is generally the lower first cost and the shelter the higher, but the gap narrows on large doors and inflatable options sit above both. Published dealer figures vary too much to quote here; the quotation prices the one that fits your door and fleet, with freight included.
- Which saves more energy?
- A correctly sized compression seal on a consistent fleet gives the tightest closure. On a mixed fleet the seal that does not fit most trailers saves nothing, and a shelter with an inflatable head curtain wins. The temperature difference across the opening decides how much any of it is worth.
- What about the gap under the leveler?
- Neither product covers it. Under-leveler seals, brush or foam, close the gap between the pit floor and the raised deck. Ask for one on cold storage docks.
- What do you need to quote?
- Door width and height, wall-to-bumper projection, dock height, approach grade, wall construction, trailer bed height range and body widths, and door type on the trailers. A photo from outside with a trailer docked is worth most of that list.
Do your own research
Official sources first. We link the rule, not a summary of the rule, wherever one exists.
- TDS 182, Technical Considerations for Dock Doors
DASMA
Dock door openings of 8 by 8 to 10 by 10 ft; shelters and seals reduce conditioned air loss when the door is raised; dock environment definitions from ANSI/LODEM MH30.3
- TDS 455, High Speed Doors and Energy Conservation Through a Building Envelope
DASMA
Air movement through an open door opening of approximately 3 feet per second
- LODEM standards: MH30.1, MH30.2, MH30.3 (2022 editions)
MHI, Loading Dock Equipment Manufacturers
The dock equipment standards family, including vehicle restraints that share the door with seals and shelters
- 29 CFR 1910.26, Dockboards
eCFR, Office of the Federal Register
Dockboard load and run-off requirements at the same opening
- Building Envelope
U.S. Department of Energy, Building Technologies Office
Envelope air leakage as an energy loss path
What we quote for this
Dock Equipment
Loading Dock Package: Leveler, Seal, Restraint, Bumpers
One quote per dock position: leveler sized to your door and fleet, seal or shelter, vehicle restraint, and bumpers.
- Leveler
- 6' or 7' wide by 6', 8', or 10' long; mechanical, hydraulic, or air-powered
- Capacity
- Sized to the heaviest forklift plus load, with safety factor
- Seal / shelter
- Compression seal or shelter sized to the door opening
Dock Equipment
Dock Edge Safety Gate
A barrier across an open dock door that stops a forklift or a person from going off the edge when no trailer is present.
- Opening
- Sized to the door width, typically 8' to 10'
- Rating
- Rated to stop a lift truck at low speed (verify per model)
- Operation
- Manual lift or powered
Dock Equipment
HVLS Fan Package for Docks and Plant Floors
High-volume, low-speed ceiling fans that move air across a dock or a bay for heat plans and air mixing.
- Diameter
- 8' to 24' (verify by model)
- Mounting
- Beam or joist mount with drop tube; structural review included
- Control
- Wall controller or building integration
Work it out
Free calculators for the numbers this decision turns on, each with a guide to the method.